Home/Glossary/High-Reliability ASICs
Semiconductor knowledge

High-Reliability ASICs

An ASIC designed and qualified for specified reliability requirements and operating conditions. Reliability depends on circuit design, process, package, production controls and the actual use environment.

← All glossary termsTechnical guide · 5 min read
In this article

An ASIC designed and qualified for specified reliability requirements and operating conditions. Reliability depends on circuit design, process, package, production controls and the actual use environment.

A reliability evidence framework
Related evidence areas with different purposes. Qualification does not by itself establish system functional safety.

Define reliability for the mission

High reliability describes a product objective that must be connected to operating conditions, lifetime and acceptable failure behavior. It is not a single design feature or a guarantee of zero failures. An industrial controller, an automotive device and a scientific instrument can face different stresses and consequences. Start with the mission profile: temperatures, supply conditions, duty cycle, mechanical environment and expected service period. Then define the evidence and controls needed to support the product's requirements, including how faults are detected, reported and managed.

Design for faults and degradation

Depending on the application, the architecture may use error detection, memory protection, monitoring or controlled recovery. These mechanisms need their own verification. A watchdog is useful only if its coverage, independence and recovery behavior match the failure scenarios. Redundancy can introduce common dependencies that undermine the intended benefit. Review what happens when a fault occurs during startup, a power transition or a critical transaction. Reliability analysis should connect each mechanism to a defined risk rather than treating a collection of protective blocks as proof of overall robustness.

Qualification and production evidence

Qualification evaluates a product against a defined set of stresses and criteria. Manufacturing controls, test coverage, traceability and ongoing monitoring support repeatability. These activities are related but not interchangeable. Passing a particular qualification does not establish every functional-safety property, and a quality-management certificate does not certify each device's application suitability. State the exact evidence and scope when making claims. For a specific project, confirm applicable customer and industry requirements with the responsible specialists rather than applying a generic high-reliability label to all conditions.

Industrial application example

Consider a controller expected to operate near machinery for many years. The requirements may emphasize stable interfaces, temperature range, diagnostic information and supply continuity. A brief laboratory test at room temperature cannot represent that service profile. Plan characterization and validation that exercise relevant operating modes and stresses, and preserve information needed to investigate field returns. Product longevity also requires change control: a later package or process change may need review even when the logical function is unchanged. Reliability is maintained through the lifecycle, not established once by a slogan.

Questions about reliability

Does high reliability mean functional safety compliance?

No. Reliability and functional safety address related but different questions. Any compliance claim requires the appropriate scope, process and evidence for the specific application.

Can a device be guaranteed never to fail?

No responsible engineering plan assumes that. Define the expected conditions, failure criteria and response mechanisms, and support the requirements with appropriate analysis, testing and production controls.

Translate the mission profile into requirements

Describe the intended environment, duty cycle, supply conditions, service duration and consequences of failure. Use those inputs to define operating limits, diagnostics and the required evidence. A broad application label does not establish a complete reliability target. Identify which requirements belong to the component and which depend on the surrounding system. Review startup, shutdown, overload and abnormal conditions as well as steady operation. The engineering plan should explain how the product is expected to behave when assumptions are violated, rather than describing only its preferred operating point.

Connect mechanisms to failure scenarios

Error detection, monitoring, redundancy and recovery need a defined purpose. State which faults a mechanism can detect and what the system does afterward. Check shared dependencies that could undermine the intended protection. A diagnostic flag is useful only if its timing, interpretation and response match the application. Verification should exercise the mechanism and its transitions, including cases where another part of the system is already degraded. Keep the analysis specific enough that reviewers can distinguish demonstrated coverage from an unsupported general claim of robustness.

Distinguish assurance evidence

Design verification, stress qualification, production screening, characterization and system validation provide different information. Do not use success in one area as proof of all the others. Record the conditions, criteria and product revision associated with each result. If a standard or customer requirement applies, confirm its exact scope with the responsible specialists and preserve the relevant evidence. A quality-management certificate describes an organizational scope; it does not automatically certify a particular chip's electrical behavior or the safety of every system in which it might be used.

Maintain control after release

Production changes, package substitutions and test-program revisions can affect the evidence supporting a product. Define review and notification responsibilities and retain the records needed for investigation. Traceability should help identify affected material when a pattern appears. Field failures need a path for diagnosis and feedback into engineering or production controls. No finite plan eliminates every possibility of failure, but disciplined requirements, appropriate evaluation and lifecycle ownership make the claims supportable and the response more effective when real-world conditions expose a problem.

A practical cross-discipline review

Before committing the next stage, bring the design, verification and product-engineering owners together around the same revision. Confirm the assumptions that pass between them: operating modes, interfaces, test access and the evidence expected at release. List unresolved issues with a responsible owner and a concrete way to close them. An open question is easier to manage when its consequence is understood than when it is hidden inside a general progress estimate. Preserve the decision record so a later change can be evaluated against the original reasoning. This review is useful even for a narrow specialist task, because the surrounding product still determines whether the delivered result is usable.

Include the receiving team's acceptance question in the review: what must be demonstrated before this result can be used safely in the next engineering stage? Agree how that demonstration will be recorded and how a subsequent change triggers a focused reassessment of the affected evidence.

Explore the related Avnet offering or discuss your project requirements.

Let's talk about your next project.

Explore design, technology enablement and manufacturing with Avnet ASIC Solutions.

Contact our team →